Autostart AS-1412 Przewodnik Instalacji Pobierz pdf

Notice

The manufacturer will accept no responsibility for any electrical damage resulting from improper

installation of the product, be that either damage to the vehicle itself or to the Unit. This Unit must

be installed by a certified technician using all safety devices supplied. Please note that this guide

has been written for properly trained Autostart technicians, a certain level of skill and knowledge is

therefore assumed. Please review the Installation Guide carefully before beginning any work.

Warning

This Unit is designed for vehicles with an automatic Transmission only. Before installing the

Unit, test that the vehicle does not start when the gear select lever is in the “Drive” position. If it

starts in gear, install a manual-transmission car starter instead.

H.3.10.S.3.20 DOC.1.01 – September 2, 2003 – CA Manufactured in Canada by Autostart

AUTOMATIC TRANSMISSION MULTI-

CHANNEL REMOTE STARTER SYSTEM

AS-1412

Installation Guide

Table of Contents

Introduction...................................................2

Included in the Package ...............................2

Before You Get Started…........................3

Harness Description .....................................4

6-Pin Main Ignition Harness.....................4

5-Pin Secondary Harness........................5

12-Pin Accessories Harness....................5

Flashing the Hood Pin ..................................8

The Programming Assistance Button (a.k.a.

PAB.) ............................................................9

Before Programming a Transmitter ..............9

How to Program the Transmitter. .................9

How to Enter Programming Options Mode...9

Programming Options.................................10

Auto Tach Programming Procedure...........11

Multi-Speed Tach Programming.................11

Testing ........................................................11

Closing Up..................................................12

Supplementary Information ........................12

Fifth Relay Output (2nd Ignition or 2nd

Accessories or 2nd Crank Output) .............12

Ignition-controlled Door Locks...............13

Secure Lock...........................................13

Passive or Active Arming Starter Kill.....13

Lock Pulse Duration ..............................13

Engine Run Time...................................13

Idle Mode...............................................13

Resetting the Module (without the plug-in

valet)...........................................................13

Resetting the Module (with the use of the

plug-in valet)...............................................14

Troubleshooting Poor Transmitting Range 14

Please note:

Button , is for the LOCK/UNLOCK functions.

Button ,, is for the START/STOP functions.

Buttons , & ,, (together) is for the TRUNK release function.

The LED is NOT included in this model.

1 2 3 4 5 6 ... 13 14

Podsumowanie treści

Strona 1 - Installation Guide

Notice The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of the product, be that either d

Strona 2

P. 10 Installation Guide AS-1412to re-enter all option selections for all functions of the Mode you are accessing. You may not skip Functions*. *NOTE

Strona 3

AS-1412 Installation Guide P. 11Auto Tach Programming Procedure NOTE:If no tach has been programmed and the ,, button is pressed, there will be no s

Strona 4

3. Test the Brake shutdown circuit: With the vehicle running under the Remote Starter,press and release the Brake Pedal. The Engine should shut down i

Strona 5

AS-1412 Installation Guide P. 13Caution: The relay output rating on this Unit is 25 A at most. Defective OEM solenoid switches can sometimes draw up

Strona 6

P. 14 Installation Guide AS-14121. FLASH the hood pin switch. 2. In ten seconds or less, press the Brake Pedal six times. 3. The Parking Lights will f

Strona 7 - ,, is pressed, etc.). The

P. 2 Installation Guide AS-1412IntroductionThis Guidebook contains all information pertinent to the installation. Most (if not all) features are grou

Strona 8 - (Cont.)

AS-1412 Installation Guide P. 3Before You Get Started…Ƈ On vehicles with a manual Transmission, always ensure that all Doors will get the Unit out o

Strona 9 - ,,to enter Mode 2

P. 4 Installation Guide AS-1412Harness Description When connecting the Module, it is important to make sure that the connector with the Ground wir

Strona 10

AS-1412 Installation Guide P. 55-Pin Secondary Harness Wire Description 1BLACK(–) Chassis ground input This wire must be connected to bare, unpainte

Strona 11 - Table 5

P. 6 Installation Guide AS-1412Note: The system also gives a Disarm pulse on this wire before remote start. 6 BLUE / WHITE (–) L.E.D. output2 V L.E.D.

Strona 12

AS-1412 Installation Guide P. 7Ignition barrel).Option 4 (Smart Ignition Re-Lock): Connects to the Negative Door trigger Input. When the Ignition Lo

Strona 13

P. 8 Installation Guide AS-141212 YELLOW(+) Glow-plug input (Cont.) -plug input on the Module may be “timed out”. The Module will power up the Ignitio

Strona 14

The Programming Assistance Button (a.k.a. PAB.)The PAB is located on the side of the Module. Thispush button mimics theHood-Pin switch in order toavo