Diagnostics - Parking Light Flash Table
Flashes Description
1
• Doors locked, Alarm and starter kill armed.
• Run time has expired.
• TRUNK button pressed.
• Start signal received by the module.
• Cold weather mode cancelled.
2
• Remote start attempt cancelled by remote.
• Doors unlocked, starter kill disarmed.
• Exiting ignition valet
• Exiting remote valet
• Power-up reset.
3
• Entering cold weather mode
• Entering ignition valet
• Entering remote valet.
• Entering extended run time.
3 slow flashes^ >after a failed start attempt | The module did not detect a tach signal.
4
• +12 V detected on the brake input wire either while cranking or during run time.
• Entering multi-speed tach programming.
5 Slow • Start attempt failed because no tach signal has been programmed.
5 Fast
• Tach signal programmed.
• New transmitter programmed.
6 • A remote start was attempted while a tach-before-crank signal was detected before cranking.
8 • Unit reset see “Resetting the Module” (p.2)
10 • A ground (-) signal was detected on the hood pin input wire.
1 - pause - 2
♦ There was a remote start attempt while the vehicle was in valet mode.
• Failed start: vehicle’s low battery voltage.
2 - pause - 2 • There was an attempt to start the vehicle while the module was in valet mode.
ON SOLID for 3
seconds^.
^followed by 1 flash Exiting cold weather mode
^followed by 3 flashes Entering cold weather mode
ON continuously • Idle mode: Idle mode is engaged
• Run time: The vehicle has been remote started and is in runtime.
ON continuously While the brake pedal is pressed. • Confirms that cold weather mode is engaged
ON 2 seconds
• The hood has been opened and a ground {-) signal has been detected on the hood pin input
wire.
ON 4 seconds • Locking or unlocking a door (with Door pulses configured to 4 sec.)
ON 20 seconds • The hood pin has been flashed and you now have access to the programming options.
ON 25 SEC.
The Hood Pin-switch has been pressed twice: the Unit went into step 1 of the Programming Centre
procedure, and no Transmitter activity was detected for 20 seconds.
Cr the Unit went into step 1 of the Transmitter Programming procedure and no activity was detected
for a few seconds. The Unit has exited the Transmitter Programming procedure.
IRREGULAR
If the unit gives irregular signals 01 to 10 flashes followed by a pause, followed by further flashes),
the system is playing back Start Failure Codes. This occurs when the Hood Pin-switch is pressed
three times.
CONSTANT
FLASHES
UP TO 60 SEC.
In Siren or Horn Mode: Alarm condition generated by an intrusion, by Panic Mode or when the
System is powered up.
To obtain a copy of the installation guide,
please visit the
http://www.autostart.ca website
click on the « Download e tab.
and
http://www.autostart.ca Installation Guide
TWO-WAY 6-BUTTON LCD AUTOMATIC TRANSMISSION
REMOTE STARTER WITH FULL ALARM SYSTEM
Quick Installation Guide
To obtain a copy of the installation guide,
please visit the http://www.autostart.ca website
click on the « Download e tab.
and
Table of Contents
How to Flash the Hood Pin
...............
....1 Supplementary Information
................
..6
Resetting the Module
........................
....2
Fifth Relay Output (2nd IGN, ACC
Transmitter Programming
or CRANK)............................................. ..6
Procedure
...........................................
....2 Tach jumper settings
...........................
..6
Entering Programming Options ....
....
2 Testing................................................... ..7
Programming Options
.......................
....
2
Diagnostics - Parking Light Flash
Multi-speed Tach Programming.... ....6
Table
......................................................
..8
Siren or Horn Timing
.........................
....6
How to Flash the Hood Pin
THE INSTALLER > THE MODULE >
• Press and hold the hood pin for 4 seconds.
• Release the hood pin.
« While the parking lights are on, press down the hood pin once more
and release the hood pin immediately.
• You now have 20 seconds to select one of the sub-menus
Parking Lights “ON”
“ON” for 20 seconds
Notice
The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of the product, be
that either damage to the vehicle itself or to the unit. This unit must be installed by a certified technician using all safety devices
supplied. Please note that this guide has been written for properly trained Autostart technicians: a certain level of skills and
knowledge is therefore assumed. Please review the installation guide carefully before beginning any work.
Warning
This remote starter is designed for vehicles with an automatic transmission only. Before installing the unit, test that the
vehicle does not start when the gear select lever is in the “Drive” position. If it starts in gear, install a manual-transmission
remote starter system instead.
DOC.1.01 R:6020 - October 30, 2006 TL Lp Manufactured in Canada
P. 8
(4 strony)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji